RAS Error Codes

The following list shows the error codes and descriptions that Remote Access Service may give in Windows NT 4.0

Value		Description
20601		Invalid Port Handle
20602		Port Already Open
20603		Buffer Too Small
20604		Wrong Info Specified
20605		Cannot Set Port Info
20606		Port Not Connected
20607		Event Invalid
20608		Device Does Not Exist
20609		Device Type Does Not Exist
20610		Buffer Invalid
20611		Route Not Available
20612		Route Not Allocated
20613		Invalid Compression Specified
20614		Out Of Buffers
20615		Port Not Found
20616		Async Request Pending
20617		Already Disconnecting
20618		Port Not Open
20619		Port Disconnected
20620		No Endpoints
20621		Cannot Open Phonebook
20622		Cannot Load Phonebook
20623		Cannot Find Phonebook Entry
20624		Cannot Write Phonebook
20625		Corrupt Phonebook
20626		Cannot Load String
20627		Key Not Found
20628		Disconnection
20629		Remote Disconnection
20630		Hardware Failure
20631		User Disconnection
20632		Invalid Size
20633		Port Not Available
20634		Cannot Project Client
20635		Unknown
20636		Wrong Device Attached
20637		Bad String
20638		Request Timeout
20639		Cannot Get LANA
20640		NetBIOS Error
20641		Server Out Of Resources
20642		Name Exists On Net
20643		Server General Net Failure
20645		Auth Internal
20646		Restricted Logon Hours
20647		Account Disabled
20648		Password Expired
20649		Not Dial In Permission
20650		Server Not Responding
20651		From Device
20652		Unrecognized Response
20653		Macro Not Found
20654		Macro Not Defined
20655		Message Macro Not Found
20656		DefaultOFF Macro Not Found
20657		File Count Not Be Opened
20658		Device Name Too Long
20659		Device Name Not Found
20660		No Responses
20661		No Command Found
20662		Wrong Key Specified
20663		Unknown Device Type
20664		Allocating Memory
20665		Port Not Configured
20666		Device Not Ready
20667		Reading INI File
20668		No Connection
20669		Bad Usage In INI File
20670		Reading Section Name
20671		Reading Device Type
20672		Reading Device Name
20673		Reading Usage
20674		Reading Max Connection BPS
20675		Reading Max Carrier BPS
20676		Line Busy
20677		Voice Answer
20678		No Answer
20679		No Carrier
20680		No Dialtone
20681		In Command
20682		Writing Section Name
20683		Writing Device Type
20684		Writing Device Name
20685		Writing Max Connection BPS
20686		Writing Max Carrier BPS
20687		Writing Usage
20688		Writing DefaultOFF
20689		Reading DefaultOFF
20690		Empty INI File
20691		Authentication Failure
20692		Port Or Device
20693		Not Binary Macro
20694		DCB Not Found
20695		State Machines Not Started
20696		State Machines Already Started
20697		Partial Response Looping
20698		Unknown Response Key
20699		Receive Buffer Full
20700		Command Too Long
20701		Unsupported BPS
20702		Unexpected Response
20703		Interactive Mode
20704		Bad Callback Number
20705		Invalid Auth State
20706		Writing Init BPS
20707		X25 Diagnostic
20708		Account Expired
20709		Changing Password
20710		Overrun
20711		RASMAN Cannot Initialize
20712		Biplex Port Not Available
20713		No Active ISDN Lines
20714		No ISDN Channels Available
20715		Too Many Line Errors
20716		IP Configuration
20717		No IP Addresses
20718		PPP Timeout
20719		PPP Remote Terminated
20720		PPP No Protocols Configured
20721		PPP No Response
20722		PPP Invalid Packet
20723		Phone Number Too Long
20724		IPXCP No Dialout Configured
20725		IPXCP No Dialin Configured
20726		IPXCP Dialout Already Active
20727		Accessing TCPCFGDLL
20728		No IP RAS Adapter
20729		SLIP Requires IP
20730		Projection Not Complete
20731		Protocol Not Configured
20732		PPP Not Converging
20733		PPP CP Rejected
20734		PPP LCP Terminated
20735		PPP Required Address Rejected
20736		PPP NCP Terminated
20737		PPP Loopback Detected
20738		PPP No Address Assigned
20739		Cannot Use Logon Credentials
20740		TAPI Configuration
20741		No Local Encryption
20742		No Remote Encryption
20743		Remote Requires Encryption
20744		IPXCP Net Number Conflict
20745		Invalid SMM
20746		SMM Uninitialized
20747		No MAC For Port
20748		SMM Timeout
20749		Bad Phone Number
20750		Wrong Module